Franklin Performance

Oil filter stud manufactured by Franklin Engineering for fitting an oil filter directly to a Nissan RB engine, slowing you to remove the oil filter...

Keep your shoulder belts or head containment net straps in place with our billet aluminium two piece piece belt guide clamps that fit 1.5" roll bar...

Bag of 50 ContaClip AP 2.5-10 2001.2 Barrier

Remote filter kit manufactured by Franklin Engineering for mounting an oil filter away from your engine, to make filter changes easier or where spa...

This billet aluminium water pump blanking cover has been designed by Franklin Performance to replace the factory water pump on all Nissan RB engine...

Billet aluminium replacement power steering pulley for 13B FD RX7 engines. Replaces the factory plastic pulley that is prone to cracking. Overall ...

Billet aluminium washer and bolt set for Mitsubishi EVO 10 4B11T engines. The set comes with 18 CNC machined washers in a selection of colours and ...

Genuine Nissan radiator top and bottom mounting rubber grommet. Application: R32 Skyline (RB20)R32 GTRR33 SkylineR33 GTRR34 SkylineR34 GTRA31 Cefir...

This pulley will give your engine bay a sleek, modern look and being larger diameter than the factory pulley will slow down your alternator. The p...

AN Spanners to prevent marking when assembling & fitting AN hose assemblies. Sizes available: 3AN (Orange) 4AN (Silver) 6AN (Black) 8AN (Blue)...

Billet aluminium blanking cap for the distributor hole in the front cover of Mazda 13B engines. CNC machined from 6061 aluminium and anodised in a ...

Push-in blanking plug to replace the PCV valve on many models of Nissan engines. Application: S14 Silvia 200sx S15 Silvia 200sx T30 X-Trail (SR20v...

Aluminium plug designed to fit into dipstick hole in a Mazda 12A / 13B / 20B rotary centre plate. Often required for dry-sump, 20B or quad rotor ap...

The GS100502 is a Gear Tooth Speed Sensor, hall-effect device designed for use in applications where ferrous edge detection/near zero speed sensing...

Heater hose bypass kit for Nissan RB Engines, to keep water flow from the rear of the engine once the heater system has been removed The kit consis...

AN Male to O-Ring Port Adaptor 8AN O-Ring to 10AN10AN O-Ring to 10AN CNC machined from billet 6061-T6 aluminium at our factory in Napier, New Zeala...

10AN rocker cover fitting for Mitsubishi Lancer Evolution X engines. It is threaded to screw straight into the factory rocker cover PCV valve port,...

Low profile remote oil filter block fitting manufactured by Franklin Performance for plumbing a remote oil filter, making filter changes easier or...

High quality 35mm2 single core black flexible cable. Sold per metre. Add the amount you require to your shopping cart and we'll cut to length for y...

Genuine Nissan crank timing belt pulleyfront plate. Fitment: R32 GTR RB26DETT R33GTR RB26DETT R34GTR RB26DETT ​AWC34 Stagea RB26DETT

Genuine Nissan Timing Belt Tensioner Bearing Spring to suit Nissan RB20E, RB20ET, RB30E & RB30ET engines. Note - This product may not be suppl...

Billet aluminium cover for electronic crank angle sensors on Mazda 13B Rotary Engines. The cover is manufactured from 6061-T6 aluminium and supplie...

Plastic oil cap to suit our billet aluminium filler necks, weld on bosses and factory Mazda Rotary engines, other than RX8 after March 2008.

Aluminium soft jaw set used for assembling anodised hose ends & fittings. Length: 100mm Colour: Black Sold as a pair.